Opcom Remote Key Programming

| 18-09-2021
[RAND-1-100] Comments

OPCOM Firmware 1.70 how to program Opel Zafira B Code Index ? Don’t worry, following us, here is the detail steps help you:

OP-COM Opel Code Index Programming Steps
Open OPCOM VAUX-COM 12309a software and go to “Diagnostics”.

Opcom Remote Key Programming Keypad

Select car year and car model: 2008 Zafira-B.

Go to “Information System”.

OPCOM Opel Auto Diagnostic Tool is a PC based diagnostic program. It covers almost all Opel cars, even new cars with CAN-BUS based diagnostic, such as Vectra-C, Astra-H, Zafira-B. The program let you to read out and clear fault codes, shows you live data, lets you to perform output test, and supports remote, and key programming. How to use OPCOM to program remote central locking Posted on September 8, 2015 by eobdtool.co.uk Here I would like to share a guide on how to guide to programming a NEW REMOTE CENTRAL LOCKING BOARD to your Astra Mk4 via op com 1.59. OP-COM is a Windows based diagnostic program package for Opel / Vauxhall cars. The diagnostic program package covers a wide range of cars from 1990-2014. Main functions are read and clear fault codes, display live data, perform output tests. Immobiliser support, remote and key fob programming. Choose “Program Code Index” function. Just choose one of index from the available index list, click “Start Programming” button. Then wait the process complete! Now Opel Coe Index Programming done by OPCOM China Clone V2014 FW V1.70! Note: OPCOM Firmware V1.70 with single layer PCB like the original PCB! Only 17GBP free shipping here.

Choose “DIS (Info Display TID, BID, GID, CID)
Select Diagnostic Connector: MS CAN
Wait and CAN enable.

Then OP-COM will show all vehicle information as below, click “Programming”.

Choose “Program Code Index” function.

Just choose one of index from the available index list, click “Start Programming” button. Then wait the process complete!
Now Opel Coe Index Programming done by OPCOM China Clone V2014 FW V1.70!

Note: OPCOM Firmware V1.70 with single layer PCB like the original PCB!

Opcom Remote Key Programming

Only 17GBP free shipping here:

http://www.obd2shop.co.uk/wholesale/opcom-can-obd2-for-opel-with-single-layer-pcb.html

Related posts:

These things you will need:

A Bosch Remote Key
An OPCOM scanner
A laptop

Remotes you can get from ebay or your local Scrap yard. Transponder Chips are identified on the chip itself, and assuming it is not a programmable one (cloned by a key cutter). OP COM you can get from Chinese sellers. Mine is from obd2diy.fr with free shipment.

Start programming:

Fire up you computer with OP COM and launch OP COM
Plug in the OP COM and Turn on the Ignition.

Opcom

From the Main menu select diagnostics (assuming you have used OP COM and configured the settings before)
Automatic does often work, but it's usually slower than just picking the year and Model.

Immobilizer

Opcom Remote Key Programming Keyless

Select Body Module, then Immobilizer.
Go to Measuring Blocks and you can see what transponder is in use and how many are programmed (You may have 2 keys but only 1 transponder ID, if you've had one Cloned at a Key cutter)
For Immobilizer programming you need to enter the Security Code from your car pass.
You can then go to Special Functions and Erase Transponder Keys. NB: This will erase all keys and may not be necessary if you have all the keys that are programmed.
Once you've erased all Transponders you can turn the ignition off and on again. The EM light will be flashing to show no valid immobilizer signal received.

Now go to Programming. Not sure the difference between Program Transponder Keys new and old, but if new doesn't work tries old.
Now you've programmed a couple of immobilizers, you can view them on the Measuring Blocks option.

Keypad

Turn the ignition off and on again to check the EM light is not flashing.

Central Locking

Opcom Remote Key Programming Remote

If your car has an Alarm then go to Anti Theft Warning, if you don't then go to Central Locking (The programming procedure is the same, but you have additional options with the alarm)
Go to Measuring Blocks, you can see what remote was used last, and the previous one.
Go to Programming, and if necessary Erase Remote Keys (This will erase all remote keys)
Go to Program Remote Key, then click the buttons on the remote you want to add (usually works first click)

If it doesn't work, make sure you have the right type of remote as mentioned at the top of this page.
Program another key if you like, and then you can view them in Measuring Blocks.

You do not need the security code for Programming the Remotes.

Hope this information is useful.